ESD Tweezer Set: What Each Tweezer Is For
🪛 ESD Tweezer Set: What Each Tweezer Is For

Tweezers handle anything too small or delicate to grab with your fingers. This 9-piece stainless steel set comes in a carrying pouch, with a different tip on each one. Here is what each one is for.

-
ESD-10: Straight Pointed Tip
A straight, pointed tip for soldering ICs and for installing and replacing small parts.
-
ESD-11: Long Fine Tip
A long, slender, fine tip for precision parts in narrow spaces.
-
ESD-12: Straight Stiff Tip
A straight tip that is wider and stiffer, for clamping boards and jobs that need a little force.
-
ESD-13: Flat Rounded Head
A flat, rounded head for lifting chips and small parts out without damaging them.
-
ESD-14: Extra-Fine Straight Tip
An extra-fine straight tip for tightly packed IC work.
-
ESD-15: Angled Beak Tip
Bent at about 45° with a beak-shaped tip, for precision work and extraction in narrow spaces.
-
ESD-16: Slender Sharp Tip
A straight, slender, very sharp tip for precision parts in narrow spaces.
-
ESD-17: Short Curved Tip
A short tip with a gentle curve for precision work and extraction. It suits smaller hands.
-
ESD34A-Sa: Flat Square Head
A flat, square, harder head for clamping parts, working component pins and simple forming.
Jump To: ⚡ Why ESD-Safe · 🔩 What They're Made Of · 🧰 How To Protect Them · 💡 Quick Tip · 🗺️ Leave It To Us
⚡ Why ESD-Safe
Some tiny electronic parts can be damaged by a static discharge as low as 20 volts, far below what you can feel, and people are one of the main sources of static.
The black ESD coating is what makes these tweezers static-safe. It lets static drain away slowly instead of zapping a part all at once. It also helps keep static from your hands from jumping through the metal tweezers into the board.
The coating works best when you're grounded too, for example with a wrist strap and a grounded mat. On its own, an ESD tool only does part of the job.
🔩 What They're Made Of
Sets like this are typically stainless steel with non-magnetic tips, so small screws and parts don't stick to them. A typical hardness is around HRC 40 to 45: hard enough to hold a fine point, with some spring in the arms.
The black finish is described as anti-static, anti-corrosion and anti-glare. It's matte and easy to grip. Specs vary from maker to maker, and on some budget sets only the tips are non-magnetic, so treat these numbers as typical rather than guaranteed.
🧰 How To Protect Them
- Store them properly. Keep each tweezer in its own slot in the pouch, never loose in a drawer, and keep tip caps on when you're not using them.
- Never pry with the tips. Even light pressure used as a lever can bend a fine tip for good. Use a pry tool or spudger instead. Dropping them and over-squeezing also knock tips out of line.
- Check the alignment. Close the tips gently and hold them up to a light. No light should pass through, and the tips shouldn't cross. A 10x loupe helps. Even a tiny offset makes the smallest parts hard to grip, and bending fine tips back usually isn't worth it. Replace them instead.
- Clean them after use. Wipe them with isopropyl alcohol and a lint-free cloth to remove flux and grease, then let them dry fully before storing.
- Protect the coating. Keep silicone hand products and sprays off the handles, since they can leave an insulating film. Harsh solvents and scrubbing may also wear the coating. If it's worn through to bare metal, don't assume it's still static-safe.
💡 Quick Tip
Use the blunt or spade tips near batteries and soft parts, and save the fine points for screws and tiny pieces. Apple's own manuals warn never to scrape or puncture a battery with tweezers.
🗺️ Leave It To Us
See every repair we do on our Repair Guides page, and check our Service Areas to see where we help.
Book An Appointment or call (720) 413-8150



